0 items in your basket. TOTAL: £0.00

View Basket My Account


Useful Info


Change Language

Your Recent Products

Cartek Solid State Battery Isolator KIT

£229.70  Excl VAT

Return to last category
Cartek Solid State Battery Isolator KIT Features

Battery Isolator Unit
Internal ON/OFF push-button
External KILL push-button
Large External Safety Sticker
Small Internal Safety Sticker
Control Switches Plug Lead
Terminal Insulation Caps
People Who Bought This Item Also Bought

HANS Clips F


Quick Discon

GP-5W Visor

3.5mm Jack E

KMX9 S Youth

GT Solid State Battery Isolator Kit 

Designed to be chassis mounted close to the vehicle’s battery allows the heavy current power cables to be kept as short as possible. Typical installation requires one external kill button and just one internal on-off switch which are all interconnected using low voltage wiring. However, the flexibility of this system also allows additional kill button/devices to be incorporated as well as full operation using just a single on/off switch if necessary. Microprocessor controlled incorporating false trigger detection, internal temperature monitoring and short-circuit protection offer unprecidented safety. At just 150g this Isolator is also incredibly light.

For Use With High Compression and V8 Engines

Size: 112x50mm
Operational Voltage: 8-18 Volts
Battery Negative Switching Current: 400-600 Amps
Operating Temperature: 0-85 degrees C

Weight: 145g
Consumption: 40 mA
Battery Positive Switching Current: 40 Amps max


Is the Isolator FIA approved?
Unlike race seats, harnesses and fire extinguishers the FIA does not have an approval procedure for Master Switches. However, most FIA race and rally championships require cars to be fitted with a spark-proof master switch to isolate the battery from all electrical systems and stop the engine. The Cartek Battery Isolator meets these requirements.

The general circuit breaker must cut all electrical circuits, battery, alternator or dynamo, lights, hooters, ignition, electrical controls, etc.) and must also stop the engine.

MSA External Circuit Breaker
8.1. The circuit breaker, when operated, must isolate all electrical circuits with the exception of those that operate fire extinguishers.

How Does It work?
The Solid State Isolator contains two isolation circuits. The first breaks the connection between the negative side of the vehicle’s battery from chassis/earth, thereby isolating the battery power from all electrical circuits, while the second cuts power to the engine electrics and thereby stops the engine from running.

Standard or GT ?
Cartek produces two types of Battery Isolator 'Standard' and GT.
We recommend the Standard Battery Isolator for normally asperated engines upto 3000cc and the GT for engines over 3000cc. We also recommend the GT version for all highly tuned race engines with high compression, turbo engines and diesel engines.
The new PDM specific Battery Isolator, CK-BSF-01, has the same power as the GT.

Why Solid State ?
Solid State means no moving parts, all power switching is fully electronic. Early types of electrical isolation were by large mechanical master-switches while more modern systems have utilised electro-mechanical solenoids. Both of these types of systems contain mechanical electrical contacts which, due to the combination of high electrical current and the shocks and vibration of the race car environment, sparking between the contacts occurs which results in contact erosion and eventual unreliability. This Solid State Isolator is also filled with a hard setting resin which prevents any ingress of dust, dirt or water therefore further increasing its stength and reliability.

How Is It Controlled?

The two electronic isolation circuits are controlled by microprocessors and incorporate various safety systems including over-temperature and over-current monitoring. These microprocessors also monitor the kill switches/buttons for instant activation without false triggering. The unit will instantly trigger into isolation mode when any of the kill buttons are struck or on detection of any fault or break in switch wiring circuits.

How Is It Operated?
The Isolator can be controlled by any number of switches although the usual configuration is one internal on-off switch and one external kill button. All switches/push-buttons are connected to the Isolator via light weight, low current wiring.
If required, multiple kill switches/devices can be incorporated, alternatively the system can be configured to be operated by a single on-off switch/pushbutton. The Isolator will also automatically trip into isolation mode if any wire connection becomes broken due to fatigue or accident.

© 2018 MSAR Ltd, 273 Kirkdale, Sydenham, London, SE26 4QD | Visit our London showroom SE26 4QD

Returns and Refunds | Terms and Conditions | Data Protection and Privacy |

HANS Stress Data | Neck Tension Comparison Chart | FIA Hans Guide | HANS Instruction Manual | HANS Owners Manual (USA) | Harness User Guide | Adjustment ranges of restraints | Webbing Information | RFR™ Rotary Buckle | ASM - anti submarining | Flexi Belt System | Hybrid Restraints | UVEX Hearing Protection | Slip Stop | Links | MSAR Blog / News | SCHROTH Training #1 How to Wrap Your Harnesses Correctly | SCHROTH Training #2 Lap Belt Specifics | SCHROTH Training #3 Flexi Laps in HD | SCHROTH Training #4 B23C Hardware in HD! | SCHROTH Training #5 B63 and B40 Hardware in HD! | SCHROTH Training #6 "Back to Basics" Belt Adjusters and Camlocks | Arai UK - Motorsport Helmet Standards Explained | A Drivers Guide to Safer Motorsport | ATL - What to think about before you call | Frontal Head Restraints (HANS) to be mandatory from 2016 | FIA Appendix J to the International Sporting Code - Article 253 Safety Equipment 2017 | FIA Appendix K to the International Sporting Code 2017 | MSA Blue Book 2017 - Section K Competitor Safety | MSA ROPS bulletin March 2011 | MSA Frontal Head Restraints (FHRs) bulletin October 2015 | MSA Rule Changes bulletin October 2017 | MSA (Abridged) ROPS bulletin October 2017 |